Skip to content Skip to sidebar Skip to footer

Readytosky M8n Gps Module Built-In Compass With Gps Antenna Mount For Standard Pixhawk 2.4.6 2.4.8 A

readytosky m8n gps module built in compass with gps antenna mount for standard pixhawk 2 4 6 2 4 8 apm 2 6 2 8 flight controller

Readytosky M8N GPS Module Built-in Compass with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 APM 2.6 2.8 Flight Controller

  • Make sure this fits by entering your model number.
  • ★★★Special designed for Pixhawk 2.4.6 2.4.8 flight controller,ASIN:B07CHQ7SZ4.(Note:If you use it to APM Flight Controller, Please replace the connect by yourself.)
  • ★The ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy.
  • ★A new generation M8N GPS,with low power consumption and high precision.
  • ★The GPS light only can light up when it search the satellite signal outdoor; ROM already been fix,it cannot be flash and change.
  • ★★★ Attention: the GPS can only use in Pixhawk and APM Flight controller,it can't work with other flight controller.

Buy Now : Readytosky M8N GPS Module Built-in Compass with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 APM 2.6 2.8 Flight Controller

Brand : Readytosky
Category : Electronics,GPS, Finders & Accessories,GPS System Accessories,Antennas
Rating : 4.3
Price : US $35.99
Review Count : 90

readytosky m8n gps module built in compass with gps antenna mount for standard pixhawk 2 4 6 2 4 8 apm 2 6 2 8 flight controller
readytosky m8n gps module built in compass with gps antenna mount for standard pixhawk 2 4 6 2 4 8 apm 2 6 2 8 flight controller
readytosky m8n gps module built in compass with gps antenna mount for standard pixhawk 2 4 6 2 4 8 apm 2 6 2 8 flight controller
readytosky m8n gps module built in compass with gps antenna mount for standard pixhawk 2 4 6 2 4 8 apm 2 6 2 8 flight controller
readytosky m8n gps module built in compass with gps antenna mount for standard pixhawk 2 4 6 2 4 8 apm 2 6 2 8 flight controller

Readytosky M8N GPS Module Built-in Compass with GPS Antenna Mount for Standard Pixhawk 2.4.6 2.4.8 APM 2.6 2.8 Flight Controller

  • Included everything shown in the photos, nicely packaged.Disassembled it, so I could figure out the wiring, and connect it up to a Beaglebone Blue (had to change plugs). PCB has informative silk for those \"do it yourself\" projects.Had some difficulty screwing the pole into the upright position, but found out a set screw was sticking out too far. Because the flat on the pole is tapered, I simply raised the pole a bit and the set screw was able to go in further.PinoutsIf you can\'t read the photo, the labels are (from top to bottom) SCL, SDA, TXD, RXD, GND, VCC.TXD and RXD are with respect to the GPS chip, so connect RXD to the Beaglebone UART_TX line and TXD to the Beaglebone UART_RX line. VCC was connect to 5V. Signals (SCL, SDA, TXD) are 3.3 volt level.Arducopter detected the GPS and compass on the first try.
  • I could not calibrate the compass on a Tarot quadcopter I just built. The unit I was using was salvaged from a crash; ;thinking that it may have been damaged, I bought this one. The module arrived on time, and as soon as I installed it I was able to complete a successful calibration. I have not yet flown the aircraft as I am waiting on a receiver, but I expect it to work just fine.
  • Plugged in to a Pixhawk 1 flight controller lived for approximately three seconds. Not impressed.
  • I ordered this GPS to use with my autopilot and as I received it I opened the case to see inside and make sure that it\'s original Ublox and it was. I used u-center program and as I connected the GPS it gave me 3 satellites in my home under the roof which is great. Also it has external compass that its very necessary, you can\'t trust internal compass on the autopilot board.
  • Very effective GPS. I used in place of the original 3DR module for 1st gen Pixhawk. It pulls many satellites and provides a really solid GPS lock. Gets a thumbs up from me
  • GPS function worked well with Omnibus Pro V3 flight controller connected to USART port 6. Take note magnetometer or compass will not work with iNav on I2C port 3 unless you solder in 4.7k resistors to both signal lines to 3.3v power
  • If you need a gps/compass module for a Pixhawk then get it. It works.
  • Worked awesome, for about 5 minutes. Now just a solid red light, and doesn’t pick up any satellites.After a quick email conversation, they sent out a new unit that works great. Definitely a satisfied customer now.

Post a Comment for "Readytosky M8n Gps Module Built-In Compass With Gps Antenna Mount For Standard Pixhawk 2.4.6 2.4.8 A"